End Cap, Handlebar, Right
This part is NO LONGER AVAILABLE. You cannot purchase this part.
|
|
|
Right handlebar end cap STYLE 1
***NOTE*** Please look closley at the back of these endcaps. These models used one of three different styles. The only what to tell them apart is by comparing the back side of the endcaps. |
* Images may not be identical to part.
# |
Part Name (Click to view) |
BOM
Qty | 001 | TRIANGULAR STICKER | 1 | 002 | Sticker, Round | 1 | 003 | Screw, Phillips Head | 5 | 005 | Screw | 4 | 011A | ALIGNMENT STICKER | 2 | 011B | RUBBER PAD | 1 | 012 | Screw, Phillips Head | 4 | 013A | Cable - pedestal, male | 1 | 013C | Cable - display to connector B | 1 | 013D | Cable, Data | 1 | 014 | PH SCREW M3*L6 | 5 | 015 | Hub Board, TR20F | 1 | 018 | Screw | 2 | 019 | CABLE CLIP 1/4" | 2 | 021A | Cup Holder, Ring | 1 | 021B | Cup Holder, Ring | 1 | 022 | Cover, Handle, Upper, Right | 1 | 023 | COVER -RIGHT HANDLE LOWER | 1 | 024 | Screw, Phillips Head | 4 | 024A | Screw | 2 | 025 | Safety Key | 1 | 026 | SAFETY KEY STICKER || W - HB6 | 1 | 026B | SERVICE STICKER | 1 | 027A | Wire, Ground | 1 | 027B | Washer, Serrated | 1 | 027C | Washer, Spring | 1 | 027D | PH SCREW M5*P0.8*L10 | 1 | 028 | Electronic board, Safety Key | 1 | 028A | CLEAR ISOLATION PLATE | 1 | 028B | SAFETY KEY SENSOR PLATE | 1 | 028C | Screw, Mushroom Top | 1 | 029 | PH SCREW M4*P0.7*L10 | 2 | 030 | BAKELITE SLEEVE D8.9*d5.1*5mm | 2 | 031 | IC BRD SET PLATE | 1 | 032 | Screw, Mushroom Top | 2 | 033 | NLA COVER-HANDLE UPPER-LEFT | 1 | 034 | COVER-CREAM -HANDLE LOWER L | 1 | 035 | HANDLE LOWER COVER STICKER | 1 | 036 | NLA End Cap, Handlebar, Right | 1 | 037 | Screw | 3 | 038 | Screw | 14 | 039 | Cover, Handlebar, Lower | 1 | 040 | Screw, Phillips Head | 2 | 041 | STICKER -ROUND D19*t0.25 | 2 | 042 | NLA End cap, Handlebar, Left | 1 | 043 | HANDLE LOWER COVER STICKER | 1 | 044 | PH SCREW M4*L14 | 2 | 045 | WATER GUARD | 1 | 046 | BAKELITE SLEEVE D9*d5.1*L8 | 2 | 047A | ALIGNMENT STICKER | 2 | 048 | Screw | 1 | 049 | CABLE CLIP | 1 | 050 | SINGLE-SIDED TAPE | 4 | 050A | INNER HEX SCREW M5*L10 | 2 | 051 | SCREW SOCKET | 2 | 052 | SERR WASHER D18*d8.5*t2.0*19T | 4 | 053 | Screw | 10 | 054 | SCREW HEAD COVER | 2 | 055 | SERRATED WASHER D18*d8.5*T2.0 | 6 | 057 | SCREW HEAD COVER, CURVED | 2 | 059A | STICKER-LEFT | 1 | 060 | BASE COVER, PEDESTAL | 2 | 061 | Lower Large Plate | 1 | 062 | MUSHROOM TOP PHILLIPS SCREW | 17 | 063 | MUSHROOM TOP PHILLIPS SCREW | 2 | 064 | Lower Access Plate | 1 | 065 | Retainer | 4 | 066 | AXLE, TRANSPORT WHEEL | 2 | 067 | Wheel, Transport | 2 | 069 | LEVELER | 4 | 070 | LEVELER | 4 | 071 | CAP | 2 | 072 | CAP, CLIP STYLE | 2 | 072A | INNER HEX SCREW M5*L10 | 2 | 073 | Sleeve | 2 | 074 | FLAT WASHER | 2 | 075 | HEX BOLT 10MM M8*L20 | 2 | 076 | CAP | 1 | 076A | STICKER-LEFT | 1 | 078 | PH SCREW M5*P0.8*L10 | 1 | 079 | CABLE CLIP 1/4" | 1 | 080 | SCREW HOLE CAP, LARGE | 2 | 081 | SPACER | 2 | 082 | FRONT COVER, EXPANSION TUBE | 1 | 083 | Sticker, Round | 2 | 084 | POWER CABLE CLIP | 1 | 085 | PRESS PLATE | 4 | 086 | TUBE CAP SET PLATE | 4 | 087 | TUBE CAP | 4 | 088 | Screw | 4 | 089 | CAP | 4 | 090 | PIVOT BOLT COVER, RIGHT | 1 | 090A | Sticker, Right | 1 | 091 | COTTER PIN | 1 | 092 | PIVOT SHOCK SLEEVE | 1 | 093 | Retainer | 1 | 094 | HEX BOLT M6*P1.0*L30 | 1 | 095 | HEX NUT M6 | 1 | 096 | MOTOR POSITION BLOCK | 1 | 097 | PH SCREW M4*L14 | 2 | 098 | FOAM STRIP W16MM*L20MM*T2mm | 2 | 099 | DRIVE BELT COVER | 1 | 100 | PH SCREW M5*P0.8*L10 | 2 | 102 | Sticker, Ground Wire | 1 | 103 | NEUTRAL WIRE STICKER | 1 | 104 | Sticker, Power Switch | 1 | 105 | Sticker, Hot Wire | 1 | 106 | PH SCREW M5*P0.8*L10 | 2 | 108 | Sticker, Motor Warning | 1 | 109 | PIVOT SHOCK SLEEVE | 2 | 110 | Shock, Pivot | 1 | 111 | PH SCREW | 2 | 112 | MICRO SWITCH | 1 | 113 | HEX BOLT M2*P0.4 | 2 | 114 | MICRO SWITCH | 1 | 115 | Screw | 2 | 117 | INCLINE MOTOR | 1 | 117A | Nylon Gear, Large | 1 | 118 | BUSHING | 1 | 119 | E-CLIP | 1 | 120 | INCLINE PIN, LOWER | 1 | 121 | COTTER PIN | 1 | 138 | DRIVE BRD | 1 | 139 | PH SCREW M5*P0.8*L10 | 4 | 140 | Screw | 4 | 142 | MOTOR COVER STICKER | 1 | 143 | Sticker, Round | 1 | 143A | STICKER - SPORTSART L252mm #3C | 1 | 144 | THERMAL SENSOR WIRE | 1 | 145 | PH SCREW M5*P0.8*L10 | 1 | 146 | Washer, Spring | 1 | 147 | Washer, Serrated | 1 | 148 | HEX SCW M8*P1.25*L20 | 4 | 149 | SPRING WASHER M8 | 4 | 150A | Washer, Flat | 4 | 151A | Wire, Sensor | 1 | 151B | Sensor, Optic | 1 | 151C | Sensor bracket | 1 | 151D | Optical wheel | 1 | 152 | Belt, Drive | 1 | 153 | COTTER PIN | 1 | 154 | AXLE D9*L40 | 1 | 156 | BUSHING D15*d8.1*L8.5 | 2 | 157 | FLAT WASHER | 2 | 158 | HEX BOLT 10MM M8*L20 | 2 | 159 | Slider Axle | 2 | 160 | Wheel, Slider | 2 | 162 | PH SCREW M5*P0.8*L10 | 2 | 163 | Rubber Cushion | 1 | 164 | INNER HEX SCREW | 2 | 165 | FLAT WASHER D12.7*d6.8*t1.0 | 2 | 165A | HIGH DENSITY FOAM d20*t5*L30(mm) | 1 | 166 | Roller, Front | 1 | 173 | Belt, Guide | 2 | 174 | BEV HD IN HEX SCW M8*P1.25*L35 | | 175 | DECK BOLT & BUSHING, REAR | 2 | 177 | BUSHING D15*d8.1*L8.5 | 2 | 178 | FLAT WASHER | 2 | 179 | HEX BOLT 10MM M8*L20 | 2 | 180 | LIFT ROTATOR COVER- LEFT | 1 | 181 | MSHRM TOP PH SCW M5*0.8*L8 | 6 | 182 | L LANDING STRIP (NOT SHOWN-SEE 423) | 1 | 183 | Foam with adhesive | 6 | 185 | MYFLEX CUSHION | 3 | 185B | Pad, Center | 2 | 186 | INNER HEX SCREW M5*L10 | 8 | 188 | Crossbar B, mid rear | 2 | 189 | SCREW SOCKET | 17 | 189A | SCREW SOCKET (METAL) | 8 | 190A | POWER FIT STICKER | 2 | 191 | NLA Cover, Tube | 1 | 192 | Screw | 2 | 193 | BUSHING | 2 | 194 | Wheel, Transport | 2 | 195 | AXLE, TRANSPORT WHEEL | 2 | 196 | Retainer | 4 | 197 | SPORTSART STICKER | 2 | 198 | Tape, Foam | 4 | 199 | FLAT WASHER D17*d8*t1.5 | 2 | 200 | INNER HEX SCREW M8*L70 | 2 | 200A | Screw | 4 | 200B | FINGER GUARD (RIGHT) | 2 | 200C | WALK DECK EXPLANATION | 1 | 201 | FOLD UP WARNING STICKER | 1 | 202 | Roller, Rear | 1 | 203 | FOAM TAPE | 6 | 204 | LANDING STRIP GROMMET | 8 | 205 | LIFT ROTATOR COVER- RIGHT | 1 | 206 | LANDING STRIP SCREW CAP- BLACK | 2 | 208 | Screw | 8 | 209 | LANDING STRIP SCREW COVER | 6 | 210 | Washer, Flat | 1 | 211 | BUSHING | 2 | 212 | E-CLIP | 1 | 213 | SET PIN | 1 | 215 | NUT M8*P1.25 | 1 | 216 | BUSHING 22*t1.5 | 1 | 217 | INNER HEX SCREW M8*L25 | 1 | 218 | RING FOR FOLDING SET | 1 | 219 | FOLD UP INDICATOR STICKER | 1 | 220 | PH SCREW M4*P0.7*L6 | 1 | 221 | LOCKING KNOB | 1 | 222 | SET KNOB SPRING | 1 | 224 | Retainer | 1 | 225 | PIN A D10*L37.5 | 1 | 226 | COTTER PIN | 1 | 227 | Cable - drive board to right pedestal | 1 | 228 | Sticker, Cable Routing | 1 | 228A | TWIST TIE | 1 | 230 | Fuse holder | 1 | 231 | Fuse, Main | 2 | 232 | Wire harness | 1 | 233 | Sticker, Fuse Holder | 1 | 234 | Screw | 1 | 235 | Washer, Spring | 1 | 236 | Washer, Serrated | 1 | 237 | Powercord inlet assy | 1 | 238 | Switch, Power | 1 | 239 | Wire - Filter to Drv board (qty 2) | 1 | 240 | Transformer | 1 | 241 | PH SCREW M5*P0.8*L10 | 2 | 243 | NLA Power Cord | 1 | 244 | PH SCREW M4*P0.7*L8 | 2 | 245 | PH SCREW M5*P0.8*L10 | 5 | 246 | CABLE CLIP 5/16" | 5 | 252 | PH SCREW M5*P0.8*L10 | 4 | 253 | FILTER (FCC) | 1 | 257 | Circuit board, HTR | 1 | 258 | Cable, HR | 1 | 259 | Transmitter, HR | 1 | 260 | WIRES - FILTER TO POWER SWITCH | 1 | 261 | CLIP | 1 | 401 | PF-T2.00F OWNER'S MANUAL | 1 | 402 | PF-T2.00F HARDWARE KIT | 1 | 403 | PF-T2.00F DISPLAY OVERLAY | 1 | 404 | HANDLE UPPER COVER | 1 | 405 | SAFETY KEY BRD AND ASSEMBLY | 1 | 406 | HANDLE LOWER COVER-CREAM | 1 | 407 | NLA End cap, Handlebar, Left | 1 | 408 | NLA End Cap, Handlebar, Right | 1 | 409 | Left pedestal | 1 | 410 | Right Pedestal | 1 | 411 | Handlebar frame | 1 | 412 | * PF-T2.00F DISPLAY ASSEMBLY | 1 | 413 | DISPLAY LOWER COVER-CREAM | 1 | 414 | DISPLAY SUPPORT | 1 | 415 | DISPLAY UPPER COVER & BRD | 1 | 416 | Board, HRC, Receiver | 1 | 417 | DISPLAY UPPER COVER & OVERLAY | 1 | 418 | Overlay, Display | 1 | 419 | MOTOR COVER | 1 | 420 | PIVOT FRAME TUBE CAP | 4 | 421 | Pivot Frame | 1 | 422 | LEVELER | 4 | 423 | LEFT LANDING STRIP | 1 | 424 | LOCKING TUBE | 1 | 425 | FOLD UP TUBE SET | 1 | 426 | REAR FRAME | 1 | 427 | Elevation Frame | 1 | 428 | MOTOR POSITIONER 132691030 | 1 | 429 | DRIVE BELT COVER | 1 | 430 | Front Pan Assembly | 1 | 431 | BRACKET, POWER SWITCH | 1 | 432 | VR, Incline | 1 | 433 | INCLINE MOTOR | 1 | 434 | MICRO SWITCH | 1 | 435 | Bolt, Deck & Bushing | 2 | 436 | DECK BOLT & BUSHING, REAR | 2 | 437 | Crossbar, front | 1 | 438 | Crossbar B, mid front | 1 | 438A | Crossbar B, mid front | 1 | 439 | Crossbar B, Mid Rear | 1 | 440 | Crossbar, rear | 1 | 441 | RIGHT LANDING STRIP | 1 | 442 | FUSE HOLDER | 1 | 443 | WALK DECK | 1 | 443A | WALK DECK | 1 | 444 | DC MOTOR | 1 | 445 | Treadbelt | 1 | 446 | LOWER CARRIAGE SET | 1 | 447 | DISPLAY | 1 | 448 | Cover, Cowling, Front | 1 | 449 | Roller, Front | 1 | 450 | AXLE, TRANSPORT WHEEL | 1 | 451 | LOCKING KNOB | 1 | | Lubrication Kit | 1 | | Treadbelt Lubricant, 4 oz | 1 | | Applicator, Lube | 1 | | POLAR HEART RATE SIMULATOR | 1 | | E PROM | 1 | |
|
